Your search for stress resulted in 18 matches...
The paper presents the results of studies on the effect of external pressure, applied on metal during squeeze casting process, on the structure of AlSi7Mg alloy. The obtained results were completed with examination...
more >>
Ordered cellular constructions are an important structural element used in armaments, aerospace and automotive industry. The use of Rapid Prototyping technique and control of solidification process allow making cas...
more >>
The wettability tests were carried out under a vacuum at 700°C in the drop/substrate couples, where drop is pure aluminium (99.999%), substrate - Ni (99.8%) and Niox (oxidized). Test were carried out...
more >>
The article examines possible use of analytical and numerical models of casting defects of a void type in determination of local increase of stresses in the vicinity of casting defect. The stress level can be one o...
more >>
The study adresses the problem of the damping capacity of metal matrix composites based on A359 alloy reinforced with 10%, 20% and 30% SiCp, subjected to multiple remelting. The aim of the research was to prove that the recycling proces...
more >>
Numerical analysis was carried out to establish the operating stress distribution in softsealed gate valves cast from ductile iron EN-GJS-400-15 for the gas network of PE pipes. The analysis was carried out with ANSYS software, based on data and d...
more >>
Decreasing the density of check valve dip balls by nearly 30% results in significant decrease in the wall thickness of the domes from which the balls are assembled. During the high pressure curing process a risk occurs of excessive deformation or ...
more >>
The paper presents a procedure that allows a quantitative comparative assessment of the flexibility of different design solutions of guide grate cast. Guide grate is an essential component part in all types of technological equipment structures us...
more >>
Thin-walled dome casts (hemispheres) with a wall thickness of 4.2 and 10.3 mm made of ductile iron underwent simulation tests within the frame of forecasting the tendency to create residual stresses, casting defects, the shaping of structures and ...
more >>
This article presents the latest tendencies within the scope of the application of computer simulation in the process of developing new solutions, including solutions in foundry practice. The functioning of Integrated Computational Materials Engin...
more >>
The publication presents the results of optimisation of parameters of complex heat treatment of as-cast AlZnMgCu(Mn) alloys consisting in retrogression and reaging (RRA, Retrogression and Re-aging). For comparison...
more >>
On the basis of assumed curves of treatment the distribution of temperature fields was determined in selected model castings achieved during heat analysis, then assuming these values as boundary conditions an integrated strength analysis was carri...
more >>
Stress measurements were taken on three castings made on the laboratory scale by different technologies from ledeburite alloy steel; the obtained results were subjected to a detailed analysis. The first casting was made by a conventional technique...
more >>
The aim of this work has been to show the influence of air oxidation and salt mist corrosion on the behaviour of low alloyed steels 18K (K18), 16M (16Mo3), 15HM (13CrMo4-4) and finally 10CrMo9-10 (10H2M) employed in the Polish energy sector. The e...
more >>
The paper presents the results of the study of Al-Si alloys with a vanadium addition used in pressure casting. The hypoeutectic Al-Si alloy grade EN AC-46000 was applied as the initial alloy. The master alloy AlV10 was introduced into the initial ...
more >>
The main aim of this investigation was to determine the microstructural degradation of Inconel 713C superalloy during creep at high homologous temperature. The alloy in as cast condition was characterized by large microstructural heterogeneity. In...
more >>
The paper presents the results of studies of hypoeutectic silumin with a chromium addition used for pressure casting. A silumin with the composition similar to that of EN AC-46000 was used as the initial one. In order to introduce chromi...
more >>
The results of testing the tendency of light metals to forming defects from the group of discontinuities - hot cracks (W-301) [1], are presented in the hereby study. These are alloys of a small or moderate tendency for hot cracking. However this t...
more >>
|