Your search for coatings resulted in 19 matches...
The article presents the results of research on the selection of optimum technological parameters of the hot-chamber die casting machine operation to make castings in AM50 magnesium alloy, coated next with the deco...
more >>
Paper presents results of investigations of selected thermophysical properties of ceramics powders RE2Zr2O7 (RE - Gd, La, Nd, Sm) type, used for thermal spray coatings. In compariso...
more >>
Dental tools are sometimes damaged as a results of exploitation or during sterilization and desinfection. The aim of durability improving of dental borers and tweezers and increasing of the biocompatibility was mod...
more >>
The article is devoted to complex studies of diamond-like coatings applied by the PAPVD technique to improve the surface of medical tools and implants in terms of better anticorrosive behaviour and biocompatibility...
more >>
The study presents the results of structure examinations and mechanical tests carried out on coatings based on Cr3Cr2-NiCr chromium carbide, applied onto the surface of ductile iron castings. The chromiu...
more >>
The article presents the results of investigations of a technology for fabrication of decorative and protective chromate coatings on die castings made from AZ91 (MgAl9Zn1) magnesium alloy. As a result of the investigat...
more >>
One of the main parameters determining proper course of the pattern evaporation process, which takes place in parallel with pouring of the foundry mould with metal, are properties of the ceramic coating applied on a po...
more >>
This paper presents the results of tests on the effect of the surface coating and flux type on the solderability of PCB by lead-free tin-based SAC305 (SnAg3.0Cu0.5) alloy determining the size of the contact angle by a wetting balance method. The s...
more >>
The paper presents the results of the effect of coating type on the amount of ionic contaminants present on printed circuit boards. The study was performed at the RT on the PCB with three types of coatings: HASL LF - lead-free, ENIG, OSP - organic...
more >>
Tests were conducted to develop a new generation of functional nano-coatings used in the foundry industry. The research focused on the introduction of modern and innovative coatings based on nanoparticles of cast elements and active chemical compo...
more >>
The studies of the drop-size effect on the wetting kinetics of the nickel substrate by lead-free solder were performed by the sessile drop method in a vacuum at a temperature of 260°C.In this work, Sn-based alloy SAC305 (Ag - 3.0 wt. %, ...
more >>
The paper focuses on the experimental investigation of wetting behavior and solderability of commercial lead-free solder on Printed Circuit Board (PCB) covered with an OSP finish (Organic Surface Protectant) characterized by physical (mechanically...
more >>
The die casting method is based on casting into permanent metal moulds, which makes it possible to obtain a large amount of casts with practically identical shapes. Compared to the technology of sand mould casting, this method has many advantages....
more >>
Protective coatings are applied in order to obtain casts with an even surface, without faults. Protective coatings can contain a solvent based on water or alcohol; however, due to their harmfulness, it is recommended to limit the use of alcohol co...
more >>
Chromium coatings modified with nanodiamond particles were deposited on aluminum alloys. The concentration of the nanodiamond particles in the chrome plating electrolyte was from 5 to 25 g/l. The thickness of the layer varied between 30 and 70 &mu...
more >>
Sintered ferrous components were coated with electrochemical chromium coatings modified with nanodiamond particles. The nanodiamond particles were produced by detonation synthesis with an average grain size 8 nm. The objective of this study was to...
more >>
This article presents selected research methods related to protective coatings used for sand moulds and cores in the foundry industry. The research methodology has been divided into studies of the technological properties of sand moulds and cores ...
more >>
The increasing requirements of casting users regarding the dimensional accuracy and surface roughness of castings force the manufacturers, i.e. foundries, to use protective coatings on moulds and cores. Coatings are applied in ...
more >>
Testing the properties of mould and core sands are specified in the norms and standards, which are used to determine the suitability of the sand for specific applications. However, the testing of protective coatings for moulding&nbs...
more >>
| 
