Your search for core resulted in 26 matches...
The article presents the results of laboratory tests on the binding characteristics of moulding sands with inorganic geopolymer binders and for comparison with furan resin and alkaline resin, designed for casting o...
more >>
The article presents the results of model tests and studies of the sand reclamation from waste moulding and core mixtures with an inorganic geopolymer binder, used in the trial production of pilot castings...
more >>
The article presents the results of laboratory and industrial tests on the application of a new geopolymer Rudal A binder used in production of moulding and core sands for castings from carbon and alloyed cast stee...
more >>
The article gives the results obtained in a fragment of the studies, carried out under a statutory activity, on optimising of the foundry sand technology with new modified inorganic binders, chemically bonded and C...
more >>
The article is a compilation of the most important results obtained during execution of own research project regarding the possibility of using fly ash formed during combustion of hard coal as a base granular material ...
more >>
This paper presents the applicability of Bio Activ PH biopreparation in the treatment of toxic substances (phenol, formaldehyde) in selected types of waste mouldings and core laboratory scale. This method has not been used for this type of waste s...
more >>
The article presents results of an investigation which constitutes a section of research under the project POIG.01.01.02-00-015/09 "Advanced materials and technologies", one of the aims which is the introduction of new ecological inorganic binders...
more >>
The presented article is the first in the series, which presents research related to the improvement of technology for producing brake blocks for the railway industry in the Spomel foundry in Lębork.The cooperation with the Foundry Research...
more >>
The presented article is the second in the series, which presents research related to the improvement of technology for producing brake blocks for the railway industry in the Spomel foundry in Lębork. The cooperation with the Foundry Research Ins...
more >>
Tests were conducted to develop a new generation of functional nano-coatings used in the foundry industry. The research focused on the introduction of modern and innovative coatings based on nanoparticles of cast elements and active chemical compo...
more >>
Results of Rctk residual strength tests are presented for samples of moulding sands prepared with a stable content of soluble sodium silicate binding agents of different WB structure indicator values, hardened in the ester pr...
more >>
The article presents the results of research on the possibilities of utilizing waste moulding sands with silicate and geopolymer binders in the production of autoclaved cellular concrete. The high content of silica in the waste moulding and core s...
more >>
The paper presents the results of analysis of gases formed under the impact of high temperature acting on moulding sands with the addition of selected organic resins and hardeners, commonly used in foundries as binders for these sands. As a resear...
more >>
The results of studies of the process of pressure-free granulation of foundry dust were described, including dust generated in the mechanical reclamation of waste bentonite sand (Dust 1), dust generated in the dry mechanical reclamation of waste s...
more >>
Loose rapid hardening masses with synthetic resins, customarily called cold-box technologies, have dominated the process of casting core production. A distinguishing feature of these technologies is the manner of mass preparation without the use o...
more >>
The increasing requirements concerning the emission of hazardous substances force the casting industry to search for new, more environment-friendly solutions. Such solutions may include technologies of developing moulding and core sands with the u...
more >>
An analysis of the drying process of surface layers of sand moulds and cores (made of loose self-hardening moulding sand with hydrated sodium silicate hardened with a liquid ester hardener) which was previously subjected to the process of moisture...
more >>
Protective coatings are applied in order to obtain casts with an even surface, without faults. Protective coatings can contain a solvent based on water or alcohol; however, due to their harmfulness, it is recommended to limit the use of alcohol co...
more >>
The main aim of this investigation was to determine the microstructural degradation of Inconel 713C superalloy during creep at high homologous temperature. The alloy in as cast condition was characterized by large microstructural heterogeneity. In...
more >>
The aim of the work was to develop and model individual elements of casting technology for the casting of a ventilated brake disc using CAD program: SolidWorks, followed by printing a core using a 3D LS ONE printer from Sand Made Lt...
more >>
This article presents selected research methods related to protective coatings used for sand moulds and cores in the foundry industry. The research methodology has been divided into studies of the technological properties of sand moulds and cores ...
more >>
Investigation results of erosion-mechanical grinding (wearing) of surfaces of foundry patterns (test samples) made of several kinds of materials are presented in the hereby paper. Investigations contained: resins, wood, painted ...
more >>
The article raises the issue of the influence of increased temperature on olivine moulding and core sands with an inorganic binder from the group of unmodified kinds of hydrated sodium silicates. Produced at laboratory conditions,&n...
more >>
The increasing requirements of casting users regarding the dimensional accuracy and surface roughness of castings force the manufacturers, i.e. foundries, to use protective coatings on moulds and cores. Coatings are applied in ...
more >>
In this paper an attempt was made to explain the phenomena accompanying the formation and destruction of bonded elements of moulds and cores in which a mixture of unmodified hydrated sodium silicate with a molar module of 2.9 (...
more >>
Testing the properties of mould and core sands are specified in the norms and standards, which are used to determine the suitability of the sand for specific applications. However, the testing of protective coatings for moulding&nbs...
more >>
| 
